Schluter RENO TK Tile to Carpet Floor Transition Profile

Description The Schluter RENO TK Tile to Carpet Floor Transition Profile is a special profile for the stepless transition of floor coverings with different heights, especially when the tiled surface is higher than the adjacent covering, e.g. the transition between tile and carpet. The visible surface area of the Schluter RENO TK Tile to Carpet Floor Transition Profile is sloped, preventing trip edges between coverings of different heights. The 6 mm profile chamber hides and protects the cut edge of lower adjoining surface coverings (e.g. carpet, vinyl flooring). The Schluter RENO TK Tile to Carpet Floor Transition Profile is available in the following material types: E = Stainless steel, 1.4301 (V2A). Available in 8mm, 10mm, 11mm, 12.5mm internal heights. EB = Brushed stainless steel. Available in 8mm, 10mm, 11mm, 12.5mm internal heights. A = Aluminium. Available in 8mm, 10mm, 12.5mm internal heights. M = Brass. Available in 8mm, 10mm, 12.5mm internal heights. AE = Anodised aluminium. Available in 8mm, 10mm, 12.5mm internal heights. Each material/internal height variation is available in either 2.5 metre or 1 metre lengths. Material properties and areas of application: In special cases the suitability of a proposed type of profile must be verified, based on anticipated chemical, mechanical and/or other stresses. Schluter RENO TK E/EB Stainless Steel is made of roll-formed stainless steel V2A (material no. 1.4301). Stainless steel is particularly well suited for applications that, in addition to heavy mechanical stresses, require resistance to chemicals such as acidic or alkaline media and detergents. Even stainless steel is not resistant to all chemical stresses, and may be affected by, e.g., hydrochloric and hydrofluoric acid or certain chloride and brine concentrations. In certain cases, this also applies to seawater pools. Special anticipated stresses should therefore be verified in advance. Schluter RENO TK M Brass are profiles made of brass. Minor marks from the manufacturing process cannot be avoided on their untreated surface areas. Brass is resistant to nearly all chemicals used in tiled environments. When exposed to air, the visible surface area of brass profiles will oxidise, resulting in a natural patina. Exposure to moisture or aggressive substances can cause heavy oxidation and spotting. Schluter RENO TK A are profiles made of aluminium. Minor marks from the manufacturing process also cannot be avoided on their untreated surface areas. The suitability of the profiles must be verified based on the anticipated chemical stresses. Since aluminium is sensitive to alkaline substances, exposure to the alkali (depending on the concentration and penetration time) may result in corrosion (aluminium hydroxide formation). Therefore, it is important to remove adhesive or grout residue from visible surfaces. In addition, ensure that the profile is solidly embedded in the setting material and that all cavities are filled to prevent the collection of alkaline water. Schluter RENO TK AE is made of clear satin anodised aluminium. The anodised layer creates a finish that retains a uniform appearance during normal use. Aggressive substances or abrasion may cause damage to the surface. Therefore, it is important to remove adhesive, mortar or grout residue from visible surfaces. Otherwise, the same statement as for aluminium applies. Installation: Select the appropriate Schluter RENO TK Transition profile according to tile thickness. Trowel tile adhesive over the area that forms the perimeter of the tiled covering. Press the trapezoid perforated anchoring leg of the Schluter RENO TK profile firmly into the adhesive and align it. Trowel additional adhesive over the perforated anchoring leg to ensure full coverage. Solidly embed the tiles so that the tiled surface is flush with the top of the Schluter RENO TK profile (the profile should not be higher than the tiled surface, but up to approximately 1 mm lower). A joint of approximately 2 mm – 3 mm should be left between the tile and the profile. Fill the joint completely with grout. Maintenance: Schluter RENO TK does not require any special maintenance. Oxidation films on brass or aluminium may be removed with a common polishing agent; however, they do reoccur. Damaged anodised finishes may only be repaired by recoating. Stainless steel surfaces exposed to the environment or aggressive substances should be cleaned periodically using a mild household cleaner. Regular cleaning maintains the neat appearance of stainless steel and reduces the risk of corrosion. All cleaning agents must be free of hydrochloric and hydrofluoric acid. Avoid contact with other metals such as steel, since this can cause rust. This also includes tools such as trowels or steel wool, i.e. tools used to remove mortar residue. We recommend the use of the stainless steel cleaning polish Schluter-CLEAN-CP. Product Datasheet Click here to view this product on the Manufacturers website.