Description ARDEX R5E Rapid Curing Solvent Free Epoxy Primer and Bonding Agent is a two-component, solvent-free, epoxy resin for use on sound concrete, cementitious surfaces, calcium sulphate-based screeds, and smoothing compounds. Ideal for use where a faster curing time is required, ARDEX R5E forms a primer/bonding layer on most dry substrates, especially smooth or dense surfaces in internal and external situations. ARDEX R5E can be used as a primer and bonding bridge prior to the application of the ARDEX range of cement-based tiling and flooring products, and on cementitious and calcium sulphate-based screeds. ARDEX R5E must be sand blinded to refusal with dry ARDEX Fine Aggregate to give a mechanical key for use as a primer prior to the application of the ARDEX K 80/SD-TB/PC-T4 Industrial Floor System, or other appropriate ARDEX cement-based products and smoothing compounds. Where substrates are very porous, more than one coat of ARDEX R5E may be required to saturate the surface and achieve the desired bonding efficiency. For applications where the relative humidity (RH) of the substrate is in excess of 75%, or where a structural damp proof membrane is not installed, ARDEX DPM 1 C should be used prior to applying ARDEX R5E. Surface Preparation: The concrete or screed substrate must be hard, sound, and free of dust and other barrier materials, such as paint, lime coatings, plaster, curing agents, laitance, adhesive residues, etc., that will inhibit adhesion to the substrate. Use a suitable degreaser to remove polish, wax, grease, oil, and similar contaminating substances prior to mechanical preparation. All substrates must be prepared using appropriate mechanical surface preparation equipment prior to applying the recommended ARDEX products. Then completely remove any dust and fines by brushing combined with effective industrial vacuum extraction equipment. The mechanical preparation is required to a suitable depth that exposes aggregate and a sound hard surface ready to receive treatment. Note: Any joints or cracks in the concrete base where differential movement is anticipated (e.g., movement joints) should be brought through to the finished surface and suitably sealed. Mixing: The individual components of ARDEX R5E Solvent Free Epoxy Primer should be thoroughly stirred before being mixed together. The entire contents of the hardener (Component B) should be poured into the resin container (Component A) and the two materials mixed thoroughly for at least 3 minutes using a heavy-duty slow-speed drill and spiral paddle. Some of the mixed components should be reintroduced back into the hardener container in order to activate any residue, and then poured back into the larger mixing vessel and re-mixed for 30 seconds (back mixing). Note: Back mixing ensures that no unreacted material is present and that the packaging can be safely disposed of as non-hazardous waste. The mixed primer has a working time of not more than 15 minutes at 20°C, after which all remaining material must not be used but must be safely discarded. Once mixed, ARDEX R5E will generate heat and lose working time if left in the mixing container or otherwise kept in bulk. Always wear suitable eye/face protection and gloves. Application: Once mixed, the material should be spread over the floor as the self-heating in the container will reduce working time. Apply using a brush or a short/medium pile roller. One or more coats may be required to ensure that a uniform coating is achieved and to compensate for differences in surface porosity. All movement joints in the subfloor must be carried through the topping and properly sealed. Construction joints and cracks not subject to movement may be overlaid, but should the floor move in any way, these defects will reflect through the system. Isolation joints will need to be allowed for in areas where high thermal movement is anticipated, e.g., around ovens and freezers. When applying ARDEX Fine Aggregate as a sand blind, ensure this is carried out whilst the ARDEX R5E is still fresh and as the application progresses. Blinding is a full covering of dry ARDEX Fine Aggregate onto the wet ARDEX R5E surface. Excess fine aggregate must be removed by brushing or vacuum after the ARDEX R5E has set, leaving a sandpaper-like finish. Packaging: 6kg units of ARDEX R5E Solvent Free Epoxy Primer are supplied in pre-gauged metal duo containers. The hardener (Component B) is in the small container, and the resin (Component A) is in the large container with sufficient space to add the hardener (Component B). Coverage: Approximately 24m² per 6kg unit. Physical Properties: Working time: 15 minutes at 20°C Walkability: 4 hours at 20°C Overcoat time: 4 hours at 20°C Product Datasheet Click here to view this product on the manufacturers website.
