Ardex K15 Levelling Compound 22kg

Description ARDEX K15 Levelling Compound is an advanced, pumpable, Rapid Drying, Heavy Duty Self-Levelling Smoothing Compound. Due to the unique rapid drying properties, ARDEX K15 can receive floorcoverings in as little as 4 hours. ARDEX K15 Levelling Compound will level and smooth, in a single application, most known uneven internal sub-floors including concrete, cement/sand screeds, porcelain, ceramic, quarry tiles and anhydrite screeds etc. prior to the installation of floorcoverings. Applications include smoothing tamped, uneven, damaged or rained-on in-situ concrete sub-floors, adjusting tolerances or camber problems between floors, slabs or pre-cast concrete, as well as smoothing old sub-floors and screeds in renovation projects. Surface preparation: The surface must be hard, sound, free of dust, dirt and other barrier materials such as grease, paint, adhesive residues or loosely adhered materials, etc. In all cases where traces of adhesive residues are present these must be sound, well adhered and unaffected by water. NOTE: For internal use only. Direct to earth sub-floors must have an effective damp proof membrane. If the damp proof membrane is absent or damaged, or the substrate is damp, please consult the ARDEX DPM 1 C or ARDEX DPM 1 C R datasheets. For residual construction moisture, consider the use of ARDEX MVS 95. Contact the ARDEX Technical Support Team for further information. Priming: All surfaces require priming. It is necessary to thoroughly prime concrete, cement/sand screeds and anhydrite-based sub-floors with ARDEX P 51 Concentrated Water-Based Primer and Bonding Agent. Consult the ARDEX P 51 data sheet for dilution ratios. As a pore sealer, ARDEX P 51 will maintain the flow life and prevent air bubbles rising through the applied ARDEX K15 mortar. ARDEX P 82 Primer and ARDEX P 4 Primer are both recommended for use on very smooth, dense and non-absorbent sub-floors, e.g. ARDEX damp proof membranes and smooth power-floated concrete. Use a suitable degreaser to remove polish, wax, grease, oil and similar contaminating substances prior to use. It is necessary to use all ARDEX Primers strictly in accordance with the relevant product data sheet, to ensure adequate adhesion of the subsequently applied ARDEX K15 Levelling Compound. If ARDEX MVS 95 has been used there is no requirement to prime this surface prior to applying ARDEX K15. Mixing: Use 5.25–5.5 litres of water per 22kg bag. Add the powder to the required amount of clean water, in a clean mixing container whilst stirring thoroughly, until a lump-free mortar is produced. Use the minimum amount of water for thick applications, or cold conditions. The use of an ARDEX mixing paddle with a 10mm chuck slow speed (600–1,000 r.p.m.) electric drill makes light work of mixing. Mixed ARDEX K15 Levelling Compound should be applied within 30 minutes at 20°C. This time is extended at lower temperatures and reduced at higher temperatures. NOTE: ARDEX K15 may be pumped using suitable floor screed mixer pump units. For advice on pumping, including suitable equipment and techniques, please contact our Technical Support Team. Application: Pour the mixed ARDEX K15 Levelling Compound onto the prepared sub-floor. The mixed mortar will flow out and self-level above 1.5mm during the first 15 minutes of its 30 minutes working time. Use a suitable steel trowel or ARDEX Pin Leveller to obtain the required thickness. A steel finishing float can be used for feather edging and touch-up work. Apply at temperatures above 5°C. NOTE: It is recommended that the floorcovering is applied within 48 hours to avoid surface crazing and contamination of the floor. Any longer than 48 hours, the surface should be covered until the floorcovering is laid. Applications over underfloor heating: Heated screeds must be laid in accordance with BS 8204 Part 1 and BS EN 1264. The underfloor heating system should have been commissioned in accordance with the manufacturer’s instruction manual and BS 8204 Part 1 and BS EN 1264 Part 4. Once commissioned and thermally cycled, the underfloor heating system should be turned down to room temperature, but not below 15°C, before the installation of ARDEX K15 Levelling Compound and the floor covering. The underfloor heating system should then be gradually brought up to normal operating temperature to avoid rapid thermal shock and wide temperature variations. Thickness: ARDEX K15 can be applied from 1.5mm up to 35mm thick. ARDEX K15 Levelling Compound should be applied at thicknesses greater than 1.5mm to benefit from its self-levelling properties. NOTE: Non-absorbent sub-floors, e.g. surface damp proof membranes, must be levelled with at least 3mm of the smoothing compound up to a maximum of 6mm thick. When applying ARDEX K15 at thicknesses of over 10mm, incorporate up to an equal volume of 3mm ARDEX COARSE AGGREGATE. For thicknesses exceeding 20mm, up to 35mm, up to an equal volume of 3–8mm clean, dry, fines-free, graded gravel may be used. Mix the ARDEX K15 as above and add the aggregate without the further addition of water. NOTE: When smoothing over flooring grade asphalt, or over sub-floors with traces of sound, hard, non-water softenable adhesive residues, use ARDITEX NA or ARDEX FA 20. Drying and hardening: Receives floorcoverings in as little as 4 hours when a high-performance adhesive is used. Rapid hardening can be walked on after 2 hours. Coverage: Approximately 1.4kg of ARDEX K15 per m² per mm thick. e.g. One 22kg bag will give enough material to cover approx 5.25m² at 3mm thick. NOTE: The coverage figure is based on a flat level surface. Additional material should be allowed for where the surface is rough or uneven. Technical Data: Bulk density of powder approx. 1.1kg/litre Weight of fresh mortar approx. 1.8kg/litre Working time at 20°C approx. 30 minutes Flow life at 20°C approx. 15 minutes Initial Set (Vicat) approx. 30 minutes Final Set (Vicat) approx. 2 hours Product Datasheet Click here to view this product on the manufacturers website.